EPB26 Plastic Plain Bearings

EPB26 Plastic Plain Bearings
Product Features |
- Suitable for soft shafts
- Excellent wear resistance
- Operation temperature up to +200℃
- Good resistance to chemicals
- High elasticity
Material Properties Data Sheet |
Material Properties | Standard | Unit | CSB-EPB26 | |
Colour | - | - | Beige | |
Density | ISO1183 | g/cm³ | 1.51 | |
Max. Moisture Absorption, 50%RH | ISO62 | % | 0.1 | |
Max. Water Absorption | ISO62 | % | 0.2 | |
Dynamic Friction Coefficient against Steel | ITS025 | μ | 0.15~0.20 | |
Max. PV Value | ITS026 | N/mm² x m/s | 0.50 | |
Flexural Modulus | ISO178 | MPa | 4500 | |
Flexural Strength | ISO178 | MPa | 95 | |
Max. Static Load | ITS027 | MPa | 55 | |
Max. Dynamic Load | ITS028 | MPa | 22 | |
Shore Hardness | ISO868 | D | 74 | |
Long-term Application Temperature | ITS029 | ℃ | +200 | |
Short-term Application Temperature | ITS029 | ℃ | +240 | |
Lowest Application Temperature | ITS029 | ℃ | -40 | |
Thermal Conductivity | ISO22007 | W/m/K | 0.24 | |
Thermal Expansion Coefficient | ISO11359 | K-1 x 10-5 | 3 | |
Flammability | UL94 | Class | V0 | |
Volume Resistance | IEC60093 | Ω·cm | >1012 | |
Surface Resistance | IEC60093 | Ω | >1012 |
*ITS: Internal test standards of CSB Compnay.
**Test temperature: 23℃ unless otherwise stated.
PV Value |
The Max. PV value of the CSB-EPB26 engineer plastic bearings is 0.5N/mm² x m/s which determines the load capacity of bearing is inversely proportional to the speed. Please refer to the chart for more detailed information (Graph EPB26-1).
Graph EPB26-1
Load, Speed and Temperature |
The allowed Max. static load of CSB-EPB26 is 55Mpa. The maximum compressive deformation rate under 55Mpa is listed in Graph EPB26-2. The actual load capacity is slightly less than 55Mpa. The load is variable against the speed and temperature. High speed causes higher temperature; Vmax. is0.9m/s, while Tmax. is 200℃. Higher temperature will decrease the load capacity of the bearing. Please refer to the Graph EPB26-3 for such variation.
|
|
Friction Factor, Wear and Shaft Material |
Graph EPB26-6
We can tell from Graph EPB26-6 that the friction factor of CSB-EPB26 is increasing along with the increase of the shaft roughness. The recommended shaft roughness is Ra0.1 to 0.6um.
CSB-EPB26 | Dry | Grease | Oil | Water |
Friction Coef. μ | 0.15~0.20 | 0.09 | 0.04 | 0.04 |
Graph EPB26-7 and Graph EPB26-8 tells that the CSB-EPB26 is very good for both hardened shaft and soft shaft. It is a excellent solution for both hardened steel shaft and stainless steel shaft. Only the hardened aluminum shaft is not a good choice. The wear resistant of CSB-EPB26 is better on rotation operation than on oscillation operation.
![]() Graph EPB26-7 | ![]() Graph EPB26-8 |
Material Features |
The chemical resistance of CSB-EPB26 is fairly good against most Acid and Alkalis.
The moisture absorption of CSB-EPB26 plastic plain bearings is 0.1% in standard atmosphere while the Max. water absorption is 0.2% in water. These values are very low so that CSB-EPB26 plastic palin bearings is very suitable for application in wet environments.
Disintegration can be possible for the material CSB-EPB26 after a long period exposed to the UV ray and its compressive strength will be reduced.
Drawing for Reference |
![]() Sleeve Bearing | ![]() Flange Bearing | ![]() Thrust Washer |
Drawing Download Link: EPB26 Drawing
EPB26 Installation Tolerances |
CSB-EPB26 Tolerances after Pressfit:
Diameter(mm) | CSB-EPB26 [E10](mm) | Housing Bore [H7](mm) | Shaft [h9](mm) |
>0~3 | +0.006~+0.046 | 0~+0.010 | 0~-0.025 |
>3~6 | +0.010~+0.058 | 0~+0.012 | 0~-0.030 |
>6~10 | +0.013~+0.071 | 0~+0.015 | 0~-0.036 |
>10~18 | +0.016~+0.086 | 0~+0.018 | 0~-0.043 |
>18~30 | +0.020~+0.104 | 0~+0.021 | 0~-0.052 |
>30~50 | +0.025~+0.125 | 0~+0.025 | 0~-0.062 |
>50~80 | +0.030~+0.150 | 0~+0.030 | 0~-0.074 |
CSB®EPB26 Standard Products |
EPB3\EPB3G\EPB9\EPB12\EPB16\EPB20\EPB21\EPB22\EPB26 Standard Specification